Thermodynamic derivative properties and densities for hyperbaric gas condensates: SRK equation of state predictions versus Monte Carlo data

The ability of Soave–Redlich–Kwong cubic equation of state (SRK EoS) to predict densities and thermodynamic derivative properties such as thermal expansivity, isothermal compressibility, calorific capacity, and Joule–Thompson coefficients, for two gas condensates over a wide range of pressures (up to 110 MPa) was studied. The predictions of the EoS were compared to Monte Carlo simulation data obtained by Lagache et al. [M.H. Lagache, P. Ungerer, A. Boutin, Fluid Phase Equilibr. 220 (2004) 221]. Two completely different alpha functions for the SRK EoS attractive term were used and their respective effects on the predictions of such properties were analyzed. Also, two different forms of the crossed terms of the attractive parameter, a_ij, and three expressions of the crossed terms of the repulsive parameter, b_ij, were combined in different ways, and predictions were carried out. Little sensitivity of the properties on the chosen alpha function, except for the calorific capacities, was found in the systems studied. The most commonly used combination rules to model phase behavior of reservoir fluids, i.e. geometric and arithmetic forms of a_ij and b_ij, respectively, predicted very deficient results for these fluids at extreme conditions, specially for density calculations.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Magnetic properties of mechanically alloyed Co–Ti powder

An amorphous phase containing traces of non-transformed Co and Ti powders was obtained by mechanical alloying nominal compositions of Co₆₇Ti₃₃ and Co₅₀Ti₅₀ in a high-energy ball-mill. These alloys were prepared from elemental powders of Co and Ti. The heat treatment of Co₆₇Ti₃₃ at 573, 873 and 1173 K crystallized nanoparticles of Co₂Ti and Co₃Ti compounds, while the same treatments conducted on Co₅₀Ti₅₀ resulted in the formation of Co₂Ti and CoTi nanoparticles. The saturation magnetizations reached a maximum value in the amorphous state and they decreased when the temperatures of the heat treatment rose. Demagnetizing interparticle interaction effects were estimated through hysteresis loops and initial magnetization curves using the Fourier technique.     

Generation of 3rd and 5th harmonics in a thin superconducting film by temperature oscillations and isothermal nonlinear current response

The generation of harmonics of the voltage response is considered when an AC current is applied through a superconducting film above T_c. It is shown that almost at all temperatures the mechanism of the temperature oscillations created by the AC current and the temperature dependence of the resistance dominates over the isothermal nonlinear electric conductivity. Only in a narrow critical region close to T_c the latter is essential for the generation of the harmonics. A detailed investigation of harmonics generation provides an accurate method for measuring the thermal boundary conductance between the film and the insulating substrate. The critical behaviour of the third harmonic will give a new method for the determination of the lifetime of metastable Cooper pairs above T_c. The comparison of the calculated fifth harmonics of the voltage with the experiment is proposed as an important test for the applicability of the employed theoretical models. Received 8 September 2001     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

掺铥氟磷玻璃的结构、热学性质和光谱性质

制备了不同Al(PO3)3含量的掺铥系列氟磷玻璃,研究了其结构、热稳定性和光谱性质。随着Al(PO3)3含量的增加,该系列玻璃的密度降低,折射率增加,差热分析表明,转变温度、析晶起始温度、析晶峰温度和熔化温度增加。Al(PO3)3摩尔浓度在7%~9%时析晶稳定性最佳。采用归一化的拉曼光谱分析了材料的结构和声子状况,对于该系列氟磷玻璃,Al(PO3)3含量的增加不会影响声子能量,但使声子密度增大。测试了样品的吸收光谱,Tm3 的3H6→3F4在第三通信窗口的L波段有明显吸收。与在其它玻璃基质中相比,Tm3 的3F4能级对应能量偏高,3H4能级对应能量偏低,使得3H4→3F4跃迁波长较大,接近于增益迁移光纤放大器的放大波长。扎得奥菲而特(Judd-Ofelt)理论分析表明随着Al(PO3)3含量增加,离子强度参量Ω2增大,Ω6保持相对稳定,Tm3 的能级寿命降低。     

Molecular dynamics simulations on the structures and properties of ε-CL-20-based PBXs ——Primary theoretical studies on HEDM formulation design

Five polymer bonded explosives (PBXs) with the base explosive ε-CL-20 (hexanitrohexaazaisowurtzi- tane), the most important high energy density compound (HEDC), and five polymer binders (Estane 5703, GAP, HTPB, PEG, and F2314) were constructed. Molecular dynamics (MD) method was employed to investigate their binding energies (Ebind), compatibility, safety, mechanical properties, and energetic properties. The information and rules were reported for choosing better binders and guiding formula- tion design of high energy density material (HEDM). According to the calculated binding energies, the ordering of compatibility and stability of the five PBXs was predicted as ε-CL-20/PEG > ε-CL-20/ Estane5703 ≈ε-CL-20/GAP > ε-CL-20/HTPB > ε-CL-20/F2314. By pair correlation function g(r) analyses, hydrogen bonds and vdw are found to be the main interactions between the two components. The elasticity and isotropy of PBXs based ε-CL-20 can be obviously improved more than pure ε-CL-20 crystal. It is not by changing the molecular structures of ε-CL-20 for each binder to affect the sensitivity. The safety and energetic properties of these PBXs are mainly influenced by the thermal capability (C°p) and density (ρ) of binders, respectively.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003